Robco CARBRA by Robco Products – Easy Fitting Instructions

PLEASE READ THE INSTRUCTIONS THOROUGHLY PRIOR TO FITTING.

Please take your time with the initial fitting of your Robco CARBRA. If fitted correctly the first time the reapplication of your Robco CARBRA will be completed quicker when next required.

Installation

• HINTS: Place the Robco CARBRA in the sun prior to fitting as this will "soften" the vinyl making it easier to fit.
• Ensure all the surfaces where the Velcro is required are clean and free of dust, dirt, and oil.
• Ensure the front of your vehicle is clean AND dry prior to fitting the Robco CARBRA

Before Installing:

Lay the Robco CARBRA flat with the felt side facing upwards. You may notice a "pocket" with Velcro fasteners sewn inside. If you have a "pocket", this MUST be fitted under the bonnet.

STEP 1	STEP 2
Lay Robco CARBRA flat with the felt facing up. Cut the supplied additional Velcro into 2cm strips. Place cut Velcro onto sewn Velcro inside "pocket" leaving the self-adhesive backing in place.	Open and secure bonnet. Place Robco CARBRA Felt side down on top of bonnet. Position bonnet inside the "pocket".
STEP 3	STEP 4
When the bonnet has been positioned securely inside the Robco CARBRA Remove self-adhesive Velcro backing and press to underside of bonnet.	Close bonnet carefully ensuring the sides of the Robco CARBRA are not in the way.
STEP 5	STEP 6
Pull Robco CARBRA over the front of the bonnet and down over licence plate and bumper. Ensure no major creases are evident between bonnet and side guards. If major creases are evident you may have to readjust the bonnet inside the "pocket".	Using the metal tabs on wheel arches of the Robco CARBRA: Bend the metal tabs around wheel arches close to the vinyl. Alternating between vehicle wheel arches, bend tabs to inside edge of wheel arch (this will ensure even fit). If fitted, secure top and bottom tabs with the Velcro supplied to wheel arch (this is not on all Robco CARBRA types).
STEP 7	STEP 8
Using the metal tabs on the bottom of the Robco CARBRA: Secure to any existing fixing points on underside of air dam / bumper by bending tabs on Robco CARBRA into place. If no fixing points, use Velcro supplied to secure tab.	Make sure the licence plate, head lights and any fog lights match up to the Robco CARBRA.

When fitted correctly your Robco CARBRA should be free of all major creases. If major creases are evident, adjust the metal tabs to tighten / loosen the Robco CARBRA. NOTE: Re-adjustment of the Robco CARBRA may be required 2 or 3 times as the Robco CARBRA "moulds" to the shape of the vehicle.

Cleaning Instructions: Whilst the Robco CARBRA is on the vehicle simply wash the vinyl with warm water and a mild detergent. To clean the underside (felt side) of the Robco CARBRA, remove it from the vehicle and hang on clothes line. Hose off the dirt and dust. Dry the vinyl side with a soft cloth. It is also recommended to hang the Robco CARBRA in the sunshine (say, over a clothes line) to allow a good airing and drying. Ensure the Robco CARBRA is COMPLETELY DRY before placing it back into the storage bag or back onto the vehicle. To keep your Robco CARBRA like new, use a vinyl protecting spray.

IMPORTANT

The Robco CARBRA is intended for use as protection against bugs, sand and stone chips whilst travelling

• The Robco CARBRA is NOT designed to be left permanently on the vehicle.
• Driving in rain will NOT reduce or affect the performance of the Robco CARBRA.
• Do not leave the Robco CARBRA on the vehicle to dry on the car surface.
• After fitting the Robco CARBRA correctly ensure that there is no movement of the bra. If movement is evident, adjust the Robco CARBRA with the metal tabs to ensure a secure fit. ROBCO will not be responsible for any damage due to incorrect fitting of the Robco CARBRA.
• If your vehicle is brand new or has recently been repaired, ensure that the paintwork has cured and hardened. Check with the manufacture or repairer of the vehicle for curing time.
• Remove the Robco CARBRA from your vehicle when not required. Keep the metal tabs bent and Velcro in place…..ready for the next time.
• Ensure the area of your vehicle where the Robco CARBRA is fitted is clean AND dry BEFORE fitting the Robco CARBRA.